How To Make A PVC Bike Rack

Do you know that purchasing a bike rack to be used for a truck may be expensive? However, most of them are too heavy to move around and can only be operated within the bed of the truck. Do you know that building a bike rack is possible? To safely move up to four bikes behind a truck by using a PVC pipe is something you can do. It will save you several dollars and time by carrying out this action.

The truth is that the rack can stand on its own. Nevertheless, you can use it within your garage to join bikes between or along trips. Is your quest on how to make a PVC bike rack? Reading through the rest part of this article will help greatly.

Make A PVC Bike Rack Easily with 9 Steps


Step 1:

You will need to have all the supplies needed for the process. This can be easily found at any hardware or improvement selling outlets. A power/strong miter saw can be considered a nice timesaver. Nevertheless, a hacksaw with elbow grease can as well work. Having some sandpaper ready is a nice idea.

Step 2:

You can cut or slice the PVC cord/ pipe to some given lengths. This can be found in the likes of 8 – 8 1/2 inch, and 12 – 1 3/4 inch, and 8 – 18 1/2 inch. When a stop block is placed at the measurement cutting point, it will make things easier. It will also make the pieces identical. You can now wipe each side using sandpaper to eliminate any cutting burrs.

Step 3:

Next on the list is to assemble 6 pipe point using one 18 1/2-inch pieces, and T connector. It should be immediately followed by the 9 1/2-inch pipe, a T-connector, and other items. You can now arrange 2 end sections using the same pattern apart from 90-degree elbows at every end. The sections should be laid in pairs.

Step 4:

Now, you can go ahead to use the 1 3/4-inch pipe pieces and join it to the paired section. Once this has been done, the 9 3/8-inch pieces should be placed between each pair.

Step 5:

By using 8 1/2-inch pipe pieces, you can structure the support area pairs. The verticals should be topped with the rest 9 3/8-inch pipe pieces on the horizontals and a T connector. Ensure to place in 90-degree elbows within the corners.

Step 6:

The main section should be perfectly connected to the support structure. You can adjust the fit by operating along a flat surface. The correct angles should be done for the T connectors and all the elbows.

Step 7:

At this juncture, you will have to test how the bike rack works. This will ensure it fits prior to gluing. Ensure to get rid of each pipe piece, one by one and finally use PVC cement on the tube prior to replacing in into position. The pieces should be placed at the right angle prior to pushing them together. This is because the glue often sets very quickly.

Step 8:

It is a nice technique to spray the PVC with paint. Though this may not be required, but can help to secure it from any damage of the sun thereby making pipe become bristle. The bike rack should be properly set when completely dry. This should be done behind the truck. However, ensure to protect the pipe ito the bed hooks by using bungee cords.

Step 9:

Lastly, you will have to set the bike in place. Now, you can go ahead to push the tire of the setup forward. This should be between the narrow are of the PVC. The bike should be properly secured. This can be done by using a bungee cord. It goes from there to the handle bar. You can simply attach the pipe hook by drilling holes within the pipe. You can as well wrap the cord/rope around the pipe.


Using this simple explanation will help you on how to make a PVC bike rack. This comprehensive step is the basis of designing a PVC bike rack easily without any stress attached. You will have to follow the steps to the letters to get the best results. Provided this can be done, you are sure to get quick and positive results. Nevertheless, the result will also last for a long time as required. Giving it a try will always help you experience total ecstasy and joy. The steps remain perfect in helping your design a PVC bike rack under no pressure.

Leave a Reply

Your email address will not be published. Required fields are marked *